ISO 9239 Flooring Radiant Panel Test Equipment ASTM E 648

              


Introduction
This surface of the material spread flame tester (ISO 9239, Flooring Radiant Panel Tester) is test method that formal reflected spread of flame on flooring material back-draft condition when fire on building happened flame at compartment or room adjacent, or high temperature gas radiated to flooring surface a hot radiation heat accumulated at upper of midway during a fire at an early growing step. 
More detail as see the next view; specimen is located at down horizon of 30 degree sloped gas radiation panel per horizon surface. 
Pilot flame as ignition resource put a part edge of specimen on high temperature side. This equipment record ignition time by spark, moving time which flame horizontal pass by specimen of length.



Standard
• ISO 9239-1:Reaction to Fire Tests for Floorings - Part 1:Determination of the Burning Behavior Using a Radiant Heat Source 
• ISO 9239-2 : Reaction to Fire Tests for Floorings - Part 2 : Determination of Flame Spread at a Heat Flux Level of 25kw/m2. 
• ASTM E 648 : Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source 
• ASTM E 970 : Standard Test Method for Critical Radiant Flux of Exposed at Attic Floor Insulation Using a Radiant Heat Energy Source 
• NFPA 253 : Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source (National Fire Codes, Vol.6) 
• KS F ISO 9239-1 : Reaction to Fire Tests for Floorings - Part 1 : Determination of the Burning Behavior Using a Radiant Heat Source 
• KS F ISO 9239-2: Reaction to Fire Tests for Floorings - Part 2 : Determination of Flame Spread at a Heat Flux Level of 25kw/m2.

Specification
- Steel frame chamber:1400(W)×500(D)×2,220(H) 
- Calcium silicate insulation board 
- Observation window 
- Sliding platform for loading of the test specimen 
- Radiant Panel:300±10mm × 450±10mm (30°, Porous cement) 
- Auto moving ignition burner 
- Scale for check flame spread 
- K-type thermocouples : Range, Ambient ~ 1,500ºC 
- Stainless steel sample holders 
- Dummy calibration panel holders for measuring heat fluxmeter 
- Pyrometer for measuring radiant panel temperature 
- Exhaust duct & hood: Ø 300 / (W)1,700 x (D)1,200 x (H)400 mm 
- Heat Flux Meter 
  Range : 0 ~ 100 ± 10 kw/m2; 
  Surface emissivity : ε=0.95± 0.05; 
- DAQ(Data Acquisition) system 
  NI-PCI DAQ Board; 
  16 Bit wide gain rage, Analog and Digital I/O Board; 
  Three A/D trigger modes; 

Ring And Size Machine(ring size & loading machine) is a professional equipment for heat exchanging coil production.

Steel Coil Reeling Machine is a kind of winding wrapping equipment for wire, wire, cable and so on, in order to achieve good protection and decorative effect; with packing speed, wide range of packaging, easy operation.
Wire winding machine is to meet the cargo assembly of storage, transport and mechanized handling operations packaging requirements, design and manufacture of the tray-winding machine, pressure-top-type resistance to pull-winding, pre-tensioning automatic film winding machine products, widely used The production cost of the products such as food, beverage, irrigation, paper making, dyestuff, plastic chemical industry, glass ceramics, electromechanical casting and so on. It can also prevent the damage of the goods during the transportation process. Cleaning effect.

Ring and Size Machine

Ring And Size Machine,Ring Loading Machine,Ring Size & Loading Machine,Steel Coil Reeling Machine

Satis Products Co., Ltd. , https://www.satismachinery.com